The resin casting handbook
Clear, hard resin pieces, measured, mixed and cured right
How much resin to mix, which ratio your label means, how long it cures, and what to do when a piece comes out sticky, cloudy, bendy or full of bubbles.
How much resin does your mold need?
Open the full resin calculator →Total to mix
108 ml3.7 fl oz
about 117 g at 1.08 g per ml (114 to 124 g across 1.05 to 1.15)
98 ml in the mold, plus 10 percent for the cup and stick.
Part A, 1:1 by volume
54 ml
1.8 fl oz
Part B
54 ml
1.8 fl oz
Layers needed
1 layer
Your label allows about 3/8 in per layer, so this mold takes 1 layer.
Includes 10 percent for what stays in the cup. Grams assume 1.08 g per ml. This is arithmetic, not a guarantee: check the depth per layer, ratio and batch size on your own label.
Something went wrong?
Sticky, cloudy, bendy or full of bubbles: find the symptom and work back to the cause.
- Resin is cloudy, milky or hazyCloudy epoxy or UV resin has 7 usual causes. Match yours in the table, then fix it: warm bottles 10 to 15 minutes, wash off blush, sand or top coat.
- Cured resin is bendy, flexible or rubberyBendy or rubbery resin usually needs more cure time: 2 to 7 more days in a warm room. A fingernail test tells a slow cure from a ratio or mixing fault.
- UV resin is sticky or tacky after curingUV resin sticky after curing? Match what you see in the table: tacky film, sticky mold side, soft inside or dense color. Fixes with lamp times and limits.
- Bubbles in epoxy or UV resinGet bubbles out of epoxy and UV resin: a where-are-the-bubbles table, heat gun and toothpick fixes, and prevention up to a 40 to 60 psi pressure pot.
- Epoxy resin is still sticky after curingEpoxy still sticky after 24 to 72 hours? Tell wet, tacky and soft-spot cures apart, find the cause, and see what warmth or a fresh coat can save.
The process, step by step
Three things to settle before you open a bottle, then five steps from the mixing cup to the finished piece.
- ·Choose your resinUV or epoxy, coating or casting: the bottle decides depth, time and tools.2 notes · 7 gear guides
- ·Workspace and safetyA warm, level, ventilated table, nitrile gloves and a cover against dust.3 notes · 1 gear guide
- ·Molds and releaseSilicone molds, release agents, and how to keep a mold clean and glossy.3 notes · 3 gear guides
- 1Measure and mixWork out the amount, split it by the ratio on the label, stir slowly.2 notes · 1 gear guide
- 2Color and add-insMica, dye and inclusions: keep the amount small and everything dry.1 note · 2 gear guides
- 3Pour and pop bubblesPour slowly inside the depth limit, then clear the bubbles while it is liquid.2 notes · 3 gear guides
- 4Cure and checkEpoxy needs warmth and time; UV resin needs the right light on both sides.5 notes · 1 gear guide
- 5Demold and finishOut of the mold, edges sanded, gloss restored, and what the piece can take.4 notes · 1 gear guide
Charts to keep by the mixing cup
Cure times, heat limits and mix ratios, taken from maker data sheets.
- Epoxy resin mixing ratio calculator: by volume and by weightPart A and Part B for any total, by volume or by weight, with a chart of common ratios.Tool
- UV resin curing time chart by lamp type, thickness and colorUV resin cure times by light source from maker instructions: 30 to 90 seconds under a UV-LED lamp, 2 to 4 minutes under a 36 W UV lamp, longer in sun.Printable
- Epoxy and UV resin heat resistance chart for coasters and traysHeat limits for named clear epoxies, in F and C, as printed on maker data sheets: use limits of 120 to 130 F and heat deflection of 100 to 122 F.Printable
- Epoxy resin cure time chart: by room temperature and resin typeEpoxy resin cure times from maker data sheets: working time, demold and full cure for coating, casting and deep pour resins, plus each maker's room range.Printable
Gear, one item at a time
Each guide compares one kind of product by what its listing states.
- Best epoxy resin mixing cups: silicone sets and graduated disposables
- Best epoxy resin dye: liquid pigments, alcohol inks and black paste
- Best large silicone molds for resin: trays, tables and deep blocks
- Best epoxy resin for outdoor use: UV resistant and marine grade picks
- Best vacuum chamber for degassing resin and silicone
- Best UV resin kit with light: starter sets for beginners
- Best UV resin for coating polymer clay and air dry clay
- Best UV resin for jewelry making: clear, hard and low odor
- Best UV light for curing resin: lamps, flashlights and wattage
- Best respirator for resin work: cartridges, fit and gloves
- Best epoxy resin polishing kit: compounds, pads and sandpaper
- Best resin molds for preserving flowers: blocks, spheres and trays
- Best resin casting powder: water ratio, finish and bag sizes
- Best pressure pot for resin casting: sizes, PSI and setup
- Best mold release spray for epoxy resin and silicone molds
- Best mica powder and pigment powder sets for epoxy and UV resin