Chart

UV resin curing time chart by lamp type, thickness and color

Published

As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.

Gear for this job

All 7 picks compared
UV light curing dental procedure for teeth whitening and health care
Photo: cottonbro studio on Pexels

Makers of craft UV resin publish cure times by light source, not by exact wattage, thickness and pigment. The chart below does the same: each row is a kind of light, with the time for a thin clear layer and the maker each figure comes from. Thickness and color are covered as rules after the chart, because no maker checked publishes minutes for them. The figures are for hard-type craft UV resin used for jewelry and small molds, not for 3D printer resin. The instructions for your own bottle and lamp win over any row.

UV resin curing time chart by light source

Times are for a thin clear layer with no color added. Let's Resin states its reference piece: a drop 20 mm across and 2 mm thick. The other makers give times for their own clear resin without stating a thickness. Where makers differ, the row shows each figure with its source.

How long to leave UV resin under the light

Start with the row for your lamp and treat it as the minimum for a thin clear layer. Let's Resin says the real time depends on the size of the piece, the glitter or pigment in it, the temperature and the weather. For a casting in a mold, cure the top, then flip the mold or the piece and cure the back for the same time. Let's Resin's tutorial gives 3 to 5 minutes per side for a full cure.

The lamp has to emit the right light. Let's Resin gives 365 to 405 nm and warns that not all nail lamps are compatible. Padico lists 405 nm for UV-LED lamps and 365 nm for UV lamps. With a weak lamp or the wrong wavelength, times stretch well past the chart or the piece stays sticky. The UV light guide compares lamps by type and wattage.

How layer thickness changes UV resin cure time

UV resin cures only as deep as the light reaches. No maker checked publishes minutes per millimeter, so the rule is to keep layers thin, about 2 to 3 mm, and cure each one before adding the next. Let's Resin asks for 2 mm or less per layer for its colored resins. Its kit manual recommends less than 5 mm per layer and several layers for big castings. Art Clay World notes that a thick, many-layered piece cures more slowly at the sides, because UV rays do not pass through the thickness easily.

Too much resin at once is a problem of its own. Let's Resin warns that a large mass can overheat and over-react, leaving a shrunken or tacky piece. The resin calculator shows how many layers a mold needs at 3 mm per layer.

How color and pigment change UV resin cure time

Art Clay World's rule of thumb is that the darker the color, the longer it takes to cure. Its instructions give 1 to 2 minutes under its lamp, with the longer time for resin that has colorant added. Let's Resin puts numbers on it for its colored UV resins: 2 to 3 minutes per side for regular colors and at least 4 to 5 minutes per side for dark ones such as gold, silver, black and dark green. Padico also says to allow a longer cure when colorant is mixed in.

Pigment blocks light, so the amount matters as much as the shade. Let's Resin keeps colorant under 5 percent of the resin volume, and Resin Rockers warns that too much mica powder can leave a piece gummy. Opaque molds block light as well. Use a translucent mold, thin layers, and cure both sides. Details are in how to color UV resin.

How to tell UV resin is fully cured

Let the piece cool first. Let's Resin says to wait 1 to 2 minutes before touching, and its manual warns that the cure gives off strong heat. Resin Rockers describes a cured piece as not sticky to the touch. It may feel slightly rubbery straight out of the lamp and keeps hardening over the next 6 to 12 hours, so handle it lightly at first.

A thin tacky film on a piece that is hard underneath is normal for many UV resins. Art Clay World states that its cured resin has a tacky surface even though it has hardened, and says to clean the film off only after the final layer. Isopropyl alcohol on a paper towel does that. If the piece is soft or wet inside, the light did not reach it: cure longer on both sides. More fixes are in why UV resin stays sticky.

Can you overcure UV resin?

Makers warn about too much power more than too much time. Let's Resin suggests a lamp above 12 W but not over 54 W: if the wattage is too high, the resin reacts too quickly and the surface crinkles or fills with bubbles. Resin Rockers also says higher wattage can cause bubbles or over-cure the resin, and adds that the only way its resin yellows is curing it too long under the lamp. Follow the chart, add time in short steps and stop when the piece is hard. See does UV resin yellow.

Note.Do not look into a UV lamp while it is on. Keep UV resin bottles and uncured pieces away from windows, because sunlight starts the cure.

Quick answers

Short answers on UV resin cure time. All times are maker figures for a thin clear layer, and the instructions for your own resin and lamp come first.

  • How long does UV resin take to cure? 30 to 90 seconds under a UV-LED lamp or 2 to 4 minutes under a 36 W UV lamp for a thin clear layer. Allow 3 to 5 minutes per side for a full cure.
  • How long to leave UV resin under light? At least the chart time for your lamp, then check it. Colored, thick or molded pieces need both sides cured, up to 4 to 5 minutes each for dark colors.
  • Can you overcure UV resin? Too much wattage wrinkles the surface, which is why Let's Resin advises not going over 54 W. Resin Rockers links very long curing to yellowing.
  • How long to cure UV resin on polymer clay? No maker checked gives a separate time for clay. Treat the coat as a thin layer on an opaque base: light reaches it only from the top.
  • How long does UV resin take to cure in the sun? Let's Resin gives 5 to 15 minutes in direct sun and 20 minutes or more under cloud. See curing UV resin without a UV light.

Use this chart

Print it, save the image version, or put it on your own site or forum post with the code below. The code keeps a link back to this page as the source.

Embed code

<a href="https://resinandmold.com/blog/uv-resin-curing-time-chart"><img src="https://resinandmold.com/charts/uv-resin-curing-time-chart/image.png" alt="UV resin curing time chart by lamp type, thickness and color" width="600" loading="lazy"></a>
<p>Source: <a href="https://resinandmold.com/blog/uv-resin-curing-time-chart">UV resin curing time chart by lamp type, thickness and color</a>, Resin and Mold</p>

What you need for this

Sources