Tool
Epoxy resin calculator by mold shape and size
Pick the shape of your mold, enter its size and get the amount to mix. No simple shape? Fill the mold with water, measure the water and enter that volume.
Short answer
Resin needed is the volume of the mold: length x width x depth, or 3.14 x radius x radius x depth for a round mold. One cubic inch is 16.4 ml and one fluid ounce is 29.6 ml. Mixed clear epoxy weighs 1.05 to 1.15 g per ml, so 100 ml is about 105 to 115 g. A round coaster 4 in across and 3/8 in deep takes about 77 ml, or 2.6 fl oz.
How much resin for common molds
One piece, no margin. Grams are a range, because mixed clear epoxy weighs 1.05 to 1.15 g per ml depending on the product.
| Mold | Size | ml | fl oz | grams |
|---|---|---|---|---|
| Round coaster | 4 in across, 3/8 in deep | 77 | 2.6 | 81 to 89 |
| Square coaster | 4 x 4 in, 3/8 in deep | 98 | 3.3 | 103 to 113 |
| Hexagon coaster | 4 in across the flats, 3/8 in deep | 85 | 2.9 | 89 to 98 |
| Rectangular tray | 10 x 6 in, 1/2 in deep | 492 | 16.6 | 516 to 565 |
| Cube | 2 in | 131 | 4.4 | 138 to 151 |
| Sphere | 2 in across | 69 | 2.3 | 72 to 79 |
| Sphere | 3 in across | 232 | 7.8 | 243 to 266 |
| Pyramid | 4 in square base, 4 in high | 350 | 11.8 | 367 to 402 |
| Flower block | 6 x 6 in, 2 in deep | 1180 | 39.9 | 1239 to 1357 |
| Keychain blank | 50 x 30 mm, 5 mm deep | 7.5 | 0.25 | 7.9 to 8.6 |
| Bookmark | 150 x 40 mm, 3 mm deep | 18.0 | 0.61 | 18.9 to 20.7 |
| Coating a panel | 12 x 12 in at 1/8 in thick | 295 | 10.0 | 310 to 339 |
Dice sets are left out on purpose: a 7-piece dice mold has no standard volume. Use the water test in the calculator instead.
Resin calculator: amount, Part A and Part B, layers
Start from a common mold or enter your own size in inches, cm or mm. The result updates as you type.
Typical products, mixed density on the data sheet: Amazing Deep Pour 1.05, ArtResin 1.05 (calculated from 1.135 and 0.967 at 1:1), EcoPoxy FlowCast 1.07, TotalBoat ThickSet 1.07 liquid (1.15 cured), Amazing Clear Cast 1.08, EpoxAcast 692 1.08, EpoxAcast 690 1.10.
Total to mix
108 ml3.7 fl oz
about 117 g at 1.08 g per ml (114 to 124 g across 1.05 to 1.15)
98 ml in the mold, plus 10 percent for the cup and stick.
Part A, 1:1 by volume
54 ml
1.8 fl oz
Part B
54 ml
1.8 fl oz
Need grams for a by-volume resin? Use the mixing ratio calculator.
Layers needed
1 layer
Your label allows about 3/8 in per layer, so this mold takes 1 layer.
1 rectangular mold, 4 x 4 x 3/8 in: mix 108 ml (54 ml Part A + 54 ml Part B).
- The margin covers resin left in the cup and on the stir stick. Set it to 0 if you already allow for it.
- Depth per layer is taken from typical data sheets. Your label decides: enter its number if it differs.
- Grams are an estimate from a density of 1.05 to 1.15 g per ml. If your resin is measured by volume, measure by volume.
- This is arithmetic, not a guarantee. Check the depth per layer, ratio and batch size on your own label.
How the numbers are worked out
The amount of resin is the volume of the mold. Every size is converted to one unit, the volume of one piece is worked out from the shape, and the result is converted to milliliters: one cubic inch is 16.387 ml, one cubic centimeter is 1 ml and one US fluid ounce is 29.5735 ml.
| Shape | Volume of one piece |
|---|---|
| Rectangle or square | length x width x depth |
| Circle (cylinder) | 3.1416 x radius x radius x depth |
| Hexagon | 0.866 x width across the flats x width across the flats x depth |
| Sphere | 3.1416 x diameter x diameter x diameter / 6 |
| Half sphere | 3.1416 x diameter x diameter x diameter / 12 |
| Pyramid | length x width x height / 3 |
| Cone | 3.1416 x radius x radius x height / 3 |
The volume of one piece is multiplied by the number of pieces, then the margin is added: with the default 10 percent, the total to mix is the net volume x 1.10. The margin stands for what stays in the cup and on the stir stick.
Grams are the total in ml multiplied by the mixed density. Data sheets for clear epoxy give 1.05 to 1.15 g per ml, so the result shows that range next to the figure for the density you set. The default of 1.08 is the middle of the published liquid values. Grams are not shown for UV resin, because that range comes from epoxy data sheets.
Part A and Part B follow from the ratio a:b on the label: Part A is the total x a / (a + b) and Part B is the total x b / (a + b). A ratio by volume splits the milliliters. A ratio by weight splits the grams. The calculator does not turn a volume ratio into grams per part, because that needs the density of each part: the mixing ratio calculator does that.
Worked example. Four round coasters, 4 in across and 3/8 in deep: one coaster is 3.1416 x 2 x 2 x 0.375 = 4.71 cubic inches, or 77.2 ml. Four take 308.9 ml, and with a 10 percent margin the total is 340 ml, which is 11.5 fl oz or about 367 g at 1.08 g per ml. At 1:1 by volume that is 170 ml of Part A and 170 ml of Part B.
How many layers a mold takes
Layers are the depth of the mold divided by the depth your resin allows in one pour, rounded up. For a sphere, half sphere, pyramid or cone the full height counts as the depth, and the amount per layer is marked as about, because those layers are not equal. The starting figures below come from maker data sheets and can be overwritten with the number on your label.
| Resin type | Default depth per layer | Basis |
|---|---|---|
| UV resin | 3 mm | Makers' reference layers are about 2 to 3 mm |
| Coating or art epoxy | 1/8 in (3 mm) | ArtResin FAQ: self-levels to about 1/8 in |
| Casting epoxy | 3/8 in (10 mm) | Alumilite Amazing Clear Cast data sheet, Smooth-On EpoxAcast 690 bulletin |
| Deep pour epoxy | 1 in (25 mm) | TotalBoat ThickSet 1 in (2 in in small molds), MAS Deep Pour 1 in, EcoPoxy FlowCast 0.5 to 1.5 in, Alumilite Amazing Deep Pour and EpoxAcast 692 up to 1.5 to 2 in |
How to measure a mold with no simple shape
Use the water test. Fill the mold with water to the level you plan to pour, tip the water into a measuring cup and read the milliliters, or weigh the water on a kitchen scale: 1 g of water is 1 ml. Pick "I know the volume" in the calculator and enter the number. Rice or sand is not needed, because water takes the exact shape of the mold.
Dry the mold completely before you pour. Water left in a mold clouds the resin. This is also the way to measure a dice set, a figurine mold or any mold with several cavities.
ml, fl oz or grams?
Measure the way the label says. A resin with a ratio by volume is measured in cups, in ml or fl oz. A resin with a ratio by weight goes on a gram scale. The two are not interchangeable: Part A is denser than Part B, so a resin that is 1:1 by volume is not 1:1 on a scale. If you only have a scale and a by-volume resin, the mixing ratio calculator converts the split with the part densities from the data sheet.
Where the numbers come from
The volumes are standard solid geometry and exact unit definitions. The depth per layer and the density figures are copied from maker data sheets: ArtResin, Alumilite Amazing Clear Cast and Amazing Deep Pour, TotalBoat ThickSet, EcoPoxy FlowCast, MAS Deep Pour and Smooth-On EpoxAcast 690 and 692. This site is independent and the calculator recommends no brand. Where your label differs from a figure here, the label wins.
- Mixing ratio calculator: Part A and Part B by volume or by weight.
- Casting resin vs coating resin: which bottle suits which depth.
- Epoxy resin cure time chart: demold and full cure by resin type.
- Epoxy resin for molds: casting resins compared by what their listings state.