Tool

Epoxy resin mixing ratio calculator: by volume and by weight

Enter the total you need, or the amount of one part you already poured, and the ratio printed on the label.

Mix ratios by volume and by weight

Independent site. Ratios are copied from maker data sheets and can change. Your label is the final word.

Sources: ArtResin Technical Data Sheet (May 2018) and FAQ; Alumilite Amazing Clear Cast Technical Data Sheet (12/2020); Alumilite Amazing Deep Pour maker data on a retailer page; EcoPoxy FlowCast Technical Data Sheet (2022); TotalBoat ThickSet Tech Data Sheet (2019); MAS Deep Pour product page; Smooth-On EpoxAcast 690 and 692 Technical Bulletin. Other 1:1 kits are left out because their by-weight figures were not found on a maker document.

What 1:1, 2:1 and 3:1 look like for a 300 ml batch

Resin ratio calculator

Works from the total, or from the amount of one part that is already in the cup. Pick the unit that matches the way your label gives the ratio.

By volume or by weight: which one is on my label?

The label or the data sheet says it in words: "1:1 by volume", "100:30 by weight", or both. If it gives one method only, that is the method to use. Some resins allow no choice: Smooth-On EpoxAcast 690 and 692 are mixed on a gram scale only, while Alumilite Amazing Clear Cast is by volume only.

The two numbers differ because Part A, the resin, is denser than Part B, the hardener. Equal volumes do not weigh the same. One art resin is 1:1 by volume but 100:84 by weight, and one deep pour resin is 3:1 by volume but 100:28 by weight.

What a wrong ratio does

A wrong ratio gives tacky or uncured resin. The usual ways to get there are weighing a resin whose ratio is by volume, loose measuring, and changing the ratio on purpose. Extra hardener does not make epoxy cure faster or harder: data sheets say an off ratio leaves the resin tacky or uncured.

If a piece is already poured, why epoxy resin stays sticky sorts the cases and the fixes, and why resin is bendy covers a piece that is hard but flexible.

How to calculate a resin ratio by hand

For a ratio of a:b, add the two numbers to get the number of shares. Part A is the total x a / (a + b) and Part B is the total x b / (a + b). Keep everything in one method: milliliters for a ratio by volume, grams for a ratio by weight.

Worked example. A 2:1 resin and a 300 ml total: 2 + 1 = 3 shares, so Part A is 300 x 2 / 3 = 200 ml and Part B is 300 x 1 / 3 = 100 ml. If Part A is already in the cup, Part B is Part A x b / a: 120 g of Part A at 100:84 by weight needs 120 x 84 / 100 = 101 g of Part B.

To turn a ratio by volume into a ratio by weight you need the density of each part from the data sheet: the weight ratio is (a x density of A) : (b x density of B). The other way round, the volume ratio is (a / density of A) : (b / density of B). The mixed density is the total weight divided by the total volume. The conversion was checked against three data sheets that publish both ratios:

The calculator never works out a weight ratio for a resin that publishes only a volume ratio unless you enter both part densities. Within one method the units convert exactly: 1 US fluid ounce is 29.5735 ml and 1 ounce by weight is 28.3495 g.

Where the numbers come from

The split is the definition of a ratio, and the conversion is density = mass / volume. The ratios and densities in the chart and the presets are copied from the maker documents listed under the chart. Makers change formulas, so where your label or data sheet differs, it wins.