Explainer

Resin mold release substitutes: what works and what does not

Published

As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.

Gear for this job

All 7 picks compared
Captivating black and white image of wet clay texture in a mold, showcasing artistry
Photo: ROMAN ODINTSOV on Pexels

This page is for two readers: one with no release spray in the house, and one with a piece stuck in a mold. It deals with two-part epoxy, because that is what the sources address. Whether you need a release at all depends on the mold material, not on the resin brand. The site does not test products. Each substitute below is listed with the source that says it works, the kind of mold that source used it on, and any warning a source gives. Where no source that was opened supports a household product, the page says so.

What does epoxy resin not stick to?

Start here, because the cheapest release is a mold that needs none. Epoxy makers publish lists of materials that cured resin peels away from. If your mold or form is made of one of these, or lined with it, skip the release.

Do you need mold release for epoxy resin?

In a silicone mold made for resin, no. Smooth-On's support article says casting resin into silicone usually needs no release, because silicone is naturally non-stick. It adds that some resins benefit from a light coat of a release made for casting, to extend mold life. For its tin-cure OOMOO silicone, Smooth-On recommends a release before casting epoxy, to prevent sticking and mold degradation. In silicone, a release is about how long the mold lasts, not about getting today's piece out.

Rigid molds are different. Resin Obsession says a mold that is not designed for resin, such as a plastic candy mold or candle mold, should definitely get a mold release. Wood, MDF and melamine forms for trays and river tables need a release or a tape lining on every face the resin touches. The molds and release pages cover each mold type.

Resin mold release alternatives: what sources say

The table lists the household substitutes people search for. A substitute counts as backed only when a source opened for this page says it works with epoxy, and only for the kind of mold that source describes. None of those sources backs a household product inside a silicone mold.

Substitutes that sources warn against or do not back

Cooking spray. The only use found is in Epoxyworks, the magazine of Gougeon Brothers, the maker of West System epoxy. It sprays the threads of a screw so the fastener can be backed out of cured epoxy. That is not a mold face that has to come out clear and glossy. Asked whether cooking spray or WD-40 can replace mold release, Katherine Swift of Resin Obsession answers no, and that mold releases meant for resin work best.

Petroleum jelly. Smooth-On sells it as a sealer and release for making silicone molds over porous models, used straight or thinned 1 part to 4 parts mineral spirits by weight. It asks for an even coat with no clumps and warns that the model surface may discolor. No source opened recommends it between resin and a mold. Resin copies the mold surface exactly, so a film thick enough to see is copied too.

Note.Epoxyworks, written for boat builders who also need epoxy to bond, advises avoiding mold releases that contain silicone, especially sprays, because overspray contaminates other surfaces.

How to apply a release agent without marking the piece

A release made for casting is the predictable choice, and the mold release spray guide lists options. Smooth-On's directions for its aerosol release are specific: hold the can 6 to 8 inches from the mold for a light, even coating. For detailed surfaces its support article describes spray, brush, spray: a light mist, a soft brush over the detail, a second light mist, then let it dry. Pooled release leaves texture and can cause surface defects.

Smooth-On also notes that released parts need thorough cleaning before staining, painting or bonding, which matters if you plan to add a top coat. For paste wax on a rigid form, Epoxyworks gives 2 to 3 coats. Whatever you use, try it on a small pour first. Smooth-On repeats that advice in its bulletins because no two applications are quite the same.

Why did my resin stick to the mold?

When resin grips a mold that should let go, one of five things has usually happened. Check them in this order: the first two cost nothing to rule out.

  • The resin did not cure. Sticky or soft resin clings to any mold, and Resin Obsession calls a release insurance for exactly this case. See why epoxy resin stays sticky.
  • It was demolded too early. Casting epoxy needs 18 to 24 hours and deep pour epoxy 24 to 72 hours before demolding. Check your label and the cure time chart.
  • The mold is not made for resin. Plastic candy molds, candle molds and other rigid plastics need a release every time, per Resin Obsession.
  • The form is bare or porous. Wood, MDF and cardboard soak up resin. Line them with packing tape before the pour.
  • The silicone is worn. Smooth-On says the life of a mold depends on what is cast in it and how often, and recommends a release with epoxy to slow mold degradation.

How to release resin from a mold when it is stuck

First make sure the resin is hard. If the open face still dents under a fingernail, give it another 24 hours in a warm spot before trying anything. Then work through these methods for silicone molds, gentlest first. Steps 2 to 5 are Resin Obsession's.

  1. 1

    Flex the mold on all sides so air gets in between resin and silicone, then push from the back of the cavity instead of pulling on the piece.

  2. 2

    Add warm soapy water to the mold and squeeze it around the piece. This makes the resin slippery and easier to release.

  3. 3

    Put the mold in the freezer for 10 to 30 minutes, then take it out and try demolding again.

  4. 4

    Or set the mold in a very hot water bath for 5 to 10 minutes. The heat may let the silicone expand and let go of the resin.

  5. 5

    As a last gentle step, apply light heat to the silicone with a heat gun while peeling the mold back from the resin.

Note.Do not pry with a knife or screwdriver: one cut in the cavity is copied onto every later piece. Wash and dry the mold afterward as in how to clean resin molds.

Quick answers

Short answers on release agents and stuck pieces. A source is named wherever a product is backed or warned against on this page.

  • Do you need mold release for epoxy resin? Not in a silicone mold. Rigid plastic molds and wood forms need a release or a packing tape lining.
  • What does epoxy resin not stick to? Silicone, polyethylene-type plastics, wax paper and the shiny side of packing tape. ArtResin also lists vinyl and acrylic.
  • What is a resin mold release alternative? For rigid forms: a packing tape lining, 2 to 3 coats of carnauba paste wax, or a PVA film, all per Epoxyworks.
  • Why is my resin sticking to my mold? Check three things first: under-cured resin, demolding too early, or a plastic mold that is not made for resin.
  • How to release resin from a mold? Flex the mold, add warm soapy water, or freeze it for 10 to 30 minutes and try again.

What you need for this

Sources