Is UV resin waterproof? What fully cured UV resin can take

Published

As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.

Gear for this job

All 6 picks compared

Fully cured UV resin is water resistant: it does not dissolve, and rinsing, rain or hand washing will not harm a properly cured piece. It is less forgiving than two-part epoxy, though. UV resin is usually applied in thin layers, and any layer that is undercured, tacky on the surface or too thin over paper, clay or wood can turn cloudy, soften or let moisture through. For jewelry, take it off before swimming, showers and dishwashing to keep it clear longer.

Why cured UV resin resists water

UV resin is a single-part acrylate resin that hardens when a photoinitiator in it reacts to UV light, usually around 365 to 405 nm. Once fully cured, it forms a solid plastic that does not absorb meaningful amounts of water. A cured cabochon or a coated charm can be rinsed and splashed without damage.

The difference from epoxy is in how it is used. Epoxy cures by chemistry everywhere it is mixed, so a thick coaster cures right through. UV resin cures only where enough light reaches it. Thick layers, dark colors, opaque pigments and shaded spots under inclusions can stay partly uncured, and those soft zones are where water does damage.

Compare UV lights for curing resin →

Tacky surfaces and undercured layers

A slightly sticky surface after curing is a common UV resin problem. Oxygen in the air slows the cure at the very top, and weak lamps, short cure times and thick layers make it worse. A tacky layer is not waterproof: water and soap can leave it cloudy or white, and it collects dust and lint.

Fix it before the piece sees water. Cure in thin layers of about 2 to 3 mm or less, give each layer the full time your lamp needs and then some, flip the piece and cure the back, and finish with a final thin clear coat cured well. If the surface is still tacky, wipe it with isopropyl alcohol and cure again, or add one more thin coat. The site's article on sticky UV resin covers the causes in detail.

Lamp choice matters as much as technique. A weak flashlight cures a thin dome on the surface but can leave the bottom of a bezel soft, and a soft base lets water creep in under the edge. A lamp with enough wattage at the wavelength your resin names, used for the full time on the bottle, cures each layer through. When in doubt, add time: overcuring a thin layer by a minute does far less harm than undercuring it, although very long cures can speed up yellowing.

Jewelry: showers, swimming and hand washing

Resin rings, pendants and earrings are fine with brief contact with water, such as washing your hands. Daily long exposure is another matter. Hot showers, soap residue, chlorinated pool water, salt water and sunscreen all slowly dull the surface and can cloud thin pieces, and hot water softens resin. Take UV resin jewelry off before showering, swimming, cleaning and using lotion.

Choose a hard type UV resin for jewelry that will be handled, and cure it fully. Soft type resin is flexible and good for bendable charms and stickers, but it scratches more easily and its surface holds water and dirt sooner. Clean resin jewelry with a damp cloth and dry it, and store pieces away from sunlight, which yellows UV resin over time.

Compare hard type UV resins for jewelry →

Sealing clay, wood and paper with UV resin

UV resin is popular as a glossy sealer over polymer clay, air dry clay, wood slices and paper. It protects them from splashes only where the coat is complete. Air dry clay in particular soaks up water and swells, so a single coat on the front with a bare back will not stop moisture; coat all sides, including edges and holes, and cure each side.

Paper and photos should be sealed with a decoupage glue or acrylic spray before resin goes on, or the resin will soak in, darken the paper and may not seal the edges. For anything that will sit in water or be washed often, such as coasters, cups and bath pieces, a two-part epoxy is the better choice: it can be poured thicker and cures fully without light.

See UV resins for coating clay →

UV resin vs epoxy for wet uses

Use UV resin for small, thin pieces where speed matters: jewelry, charms, keychains, bezels, small repairs and glossy topcoats. Use epoxy for anything thick, large or regularly wet: coasters, trays, bath trays, tumblers, table tops and outdoor pieces. Epoxy cures through any depth and color, has more working time and costs less per ounce.

Both yellow with long sun exposure, and both soften in hot water. Neither should go in a dishwasher. If you are unsure which a project needs, the comparison article on UV resin vs epoxy resin on this site goes through the differences project by project.

See UV resin kits with a light →

Frequently asked questions

Can you shower with UV resin jewelry? Brief splashes will not ruin a well cured piece, but regular hot showers with soap dull and cloud it over time. Take it off.

Why did my UV resin turn white or cloudy in water? It was not fully cured, the surface was still tacky, or the water was hot. Cure longer in thinner layers and add a final clear coat.

Is UV resin waterproof enough for a fish tank or vase? Not reliably. Use a fully cured two-part epoxy sold for that purpose, or glass.

Does UV resin need a sealer to be waterproof? No, a fully cured UV resin surface is its own seal. A final thin coat of UV resin is the usual finish if the surface stays tacky.

What you need for this