How to make resin coasters with pictures: sealing, placing and pouring
Published
As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.
Gear for this job
All 7 picks comparedLET'S RESIN casting resin kit, 34 oz
See price on AmazonSee it on AmazonLET'S RESIN deep pour epoxy resin, 51 oz
See price on AmazonSee it on AmazonTeexpert clear epoxy resin kit, 64 oz
See price on AmazonSee it on Amazon
To make resin coasters with pictures, print or cut the photo slightly smaller than the mold, seal both sides with a clear sealer such as Mod Podge or clear packing tape, pour a thin layer of epoxy, lay the sealed photo face down on the tacky resin, and fill the mold. Sealing is the step that matters: unsealed paper soaks up resin and turns dark, blotchy or see-through. The rest is ordinary coaster making with a two-layer pour.
Which pictures and prints work best
Laser prints and photo lab prints hold up better than inkjet prints on plain paper. Inkjet ink can bleed or smear when a water-based sealer goes over it, so let inkjet prints dry for a day and use a spray sealer for the first coat. Glossy photo paper works, but its coating can trap small air pockets at the edges, so seal it well. Thin papers such as napkins, magazine pages and tissue paper give a translucent, faded look once resin soaks in; seal them if you want them to stay opaque.
Size the picture about 1/8 to 1/4 in smaller than the mold on every side, so resin flows around it and closes the edge. A paper edge that touches the mold wall wicks resin and leaves a visible line or a pale halo on the finished coaster. For a 4 in round mold, a circle of about 3.5 in is a safe size. A small punch or a circle cutter makes clean round photos.
Sealing the photo so it does not darken
Paper is porous. When epoxy reaches the fibers, it fills the air spaces and the paper turns darker and more transparent, which is why an unsealed photo can show the back side or look wet and blotchy. A sealer closes the paper before the resin touches it.
Three methods are common. A decoupage glue such as Mod Podge, brushed thinly on the front, left to dry, then on the back and on the edges, with two coats per side. A clear acrylic spray sealer, two or three light coats per side, which avoids brush marks on delicate prints. Or clear packing tape or a laminating pouch, which seals completely and is the most reliable for inkjet prints, though tape can show its edge and lamination makes the picture thicker. Whatever you use, let it dry fully, usually a few hours, before it meets resin. A damp sealer can cloud the epoxy around the picture.
How much resin and which epoxy
A 4 in round coaster 1/4 in deep holds about 1.7 fl oz, so plan on 2 oz of mixed resin per coaster and about 8 to 9 oz for a set of four. The picture adds almost no volume. Mix a little extra for the first thin layer, which you mix separately from the main pour if you want time for it to gel.
Use a clear casting or coating epoxy that cures in thin layers and states a non-yellowing formula; yellowing is more visible over a white photo than over colored resin. Keep any color in the back layer only. A tinted top layer sits over the picture and changes its colors.
The two-layer pour, step by step
Measure and mix the epoxy at its exact ratio for at least three minutes, scraping the cup walls. Pour a thin first layer, about 1/8 in, into each mold. Pop the bubbles with a heat gun, then leave it to gel for 2 to 4 hours, until a gloved finger leaves a mark but no resin sticks to it.
Lay the sealed picture face down on the tacky layer, starting at one edge and lowering it like a phone screen protector so air is pushed out ahead of it. Press gently from the center outward with a gloved finger or a silicone stick. Then mix a fresh batch and pour the rest of the coaster over the back of the photo. If you want a solid back, color this second layer with an opaque white or black dye so the picture has a clean backing. Pop the bubbles again and cover the molds to keep dust off while it cures.
Fixing floating pictures and trapped bubbles
A picture that floats up or tilts was usually placed on resin that was still too liquid. Wait until the first layer is tacky, or hold the picture down with a dab of resin at each edge and let that set before the main pour. Lightweight photos can also be weighted with a clean, flat object for the first 20 minutes, then removed before the resin gels.
Silver bubbles under the picture come from air trapped between the photo and the first layer, or from unsealed paper letting out air. Seal the photo on both sides and edges, press it down from the center outward, and pop bubbles on the first layer before the picture goes in. Bubbles that are already cured under the photo cannot be removed, so a test coaster with a spare print is worth the 2 oz of resin.
Demolding and finishing photo coasters
Demold after 24 to 48 hours and leave the coasters at least 72 hours before use. Sand any sharp lip on the edge with wet sandpaper from about 320 up to 600 or higher, and add cork or felt pads to the back. Because the picture is face down in the mold, the front of the coaster is the glossy mold side, so glossy molds give the clearest view of the photo.
Photo coasters are popular gifts, so test a finished one with a hot mug before giving a set. Standard epoxy can soften under very hot cups, and a picture close to the surface shows any marks more.
Frequently asked questions
Can I put a photo in resin without sealing it? You can, but the paper will usually darken, turn patchy or let the image on the back show through. Sealing both sides takes a few minutes and prevents it.
Can I use a regular inkjet print? Yes, if you seal it with a spray sealer first, or with clear tape or lamination. Brushing a water-based glue straight onto fresh inkjet ink can smear it.
Should the picture face up or down? Face down in the mold, so the image looks out through the glossy bottom of the mold, which becomes the top of the coaster.
Can I use UV resin for photo coasters? UV resin can seal a photo or fill a thin bezel, but for a full 1/4 in coaster a two-part epoxy is cheaper and cures more reliably through the full depth.
What you need for this
- See price on AmazonAmazon
LET'S RESIN casting resin kit, 34 oz
From Best epoxy resin for silicone molds: clear casting picks
- See price on AmazonAmazon
LET'S RESIN 350W dual temp heat gun for resin
From Best heat gun for resin art: popping bubbles without damage
- See price on AmazonAmazon
Let's Resin Resin Polishing Kit, 33 Pieces
From Best epoxy resin polishing kit: compounds, pads and sandpaper
- See price on AmazonAmazon
TCP Global Graduated Mixing Cups, 10 oz, 50 Box
From Best epoxy resin mixing cups: silicone sets and graduated disposables