How to make resin coasters: molds, amounts, pouring and finishing
Published
As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.
Gear for this job
All 7 picks comparedLET'S RESIN casting resin kit, 34 oz
See price on AmazonSee it on AmazonLET'S RESIN deep pour epoxy resin, 51 oz
See price on AmazonSee it on AmazonTeexpert clear epoxy resin kit, 64 oz
See price on AmazonSee it on Amazon
To make resin coasters, mix a clear casting or coating epoxy at its exact ratio, pour it about 1/4 in deep into silicone coaster molds, pop the bubbles with a heat gun or torch, and leave it covered for 24 to 48 hours before demolding. A standard 4 in round coaster takes about 2 oz of mixed resin, so a set of four needs roughly 8 to 9 oz once you allow for what stays in the cup. The steps below cover the choices that decide whether the set comes out clear, flat and usable under a hot mug.
What you need before you start
The kit list is short: a two-part epoxy, silicone coaster molds, graduated mixing cups, a stir stick you can scrape with, nitrile gloves, a heat gun or small torch, a level surface and a cover such as a plastic tub to keep dust off while it cures. Optional extras are mica powder or resin dye, dried flowers, glitter, cork or felt pads for the back, and fine sandpaper for the edges.
Choose the epoxy by the depth of the pour. Coaster molds are usually 1/4 to 3/8 in deep, which most art and coating epoxies handle in one pour. A casting resin with a longer working time gives you more time to place flowers and pop bubbles, while a fast coating epoxy can heat up and set before you finish a set of six. Work in a room at 70 to 80 F; cold resin is thick, traps bubbles and cures slowly. Epoxy also gives off vapors while it cures, so ventilate the room and wear a respirator with organic vapor cartridges if you pour often.
How much resin each coaster needs
Work out the volume instead of guessing. For a round mold, multiply 3.14 by the radius squared and by the depth, all in inches, to get cubic inches, then multiply by 0.554 to get fluid ounces. A 4 in round coaster at 1/4 in deep is 3.14 x 2 x 2 x 0.25 = 3.14 cubic inches, which is about 1.7 fl oz. A 4 in square at the same depth is 4 cubic inches, about 2.2 fl oz.
Add 10 to 15 percent for resin that stays on the cup walls and stir stick. For a set of four round coasters, mix about 8 oz in total: 4 oz resin and 4 oz hardener for a 1:1 epoxy. If you are coloring each coaster differently, mix one clear batch and split it into small cups before adding color, so every coaster gets resin from the same correctly measured mix.
Mixing and coloring the epoxy
Measure by the method your resin states, by volume or by weight, and never adjust the ratio to make it cure faster. Pour the resin first, then the hardener, and stir slowly for at least three minutes, scraping the sides and bottom of the cup several times. Unmixed resin clinging to the walls is the usual cause of soft or sticky patches in a finished coaster. Many crafters pour the mix into a second clean cup and stir another minute to be sure.
Add color after mixing. Mica powder gives shimmer and metallic swirls, a translucent liquid dye tints the resin like stained glass, and an opaque paste gives solid white or black backgrounds. Keep colorant to a small fraction of the batch, around 5 percent at most for most brands, and less is usually enough. Alcohol ink dropped onto the surface after pouring makes cells and petri effects but should not be stirred into the whole batch in quantity.
Pouring, adding inclusions and popping bubbles
Set the molds on a level board before you pour, so you can move them later without bending the silicone. Pour slowly from a low height into the center of each mold and let the resin spread to the edges. For dried flowers, leaves or photos, pour a thin first layer of about 1/8 in, let it gel for a few hours until tacky, place the items face down, then pour the rest. Flowers placed in the first liquid pour tend to float and tilt.
Bubbles rise within the first 10 to 15 minutes. Pass a heat gun or small torch quickly over the surface, a few inches away, and keep it moving. Holding heat in one spot can scorch the resin or warp the mold. Check again after 15 minutes and repeat if more bubbles have surfaced. Then cover the molds with a box or tub to keep out dust and hair, and leave them untouched.
Demolding, sanding edges and finishing
Most epoxies can be demolded after 24 to 48 hours at room temperature, but they reach full hardness only after about 72 hours, and some brands say up to 7 days. If a coaster bends when you flex the mold, leave it longer. Peel the silicone back from the edges instead of pushing the coaster out from the middle.
Edges often have a sharp lip where resin climbed the mold wall. Sand it flat with wet sandpaper, starting around 220 or 320 grit and going up to 600 or higher, then polish or brush a thin coat of resin over the edge to restore the shine. Finish by sticking cork, felt or silicone pads to the back so the coaster does not scratch the table and sits flat.
Making coasters that survive hot mugs
Standard art epoxy softens at roughly 120 to 140 F, and fresh coffee or tea is well above that, so a hot mug can leave a ring or a dent in a coaster that was not made with heat in mind. Three things help. Let the resin fully cure for at least a week before the coasters see hot drinks. Use an epoxy that states a higher heat resistance in its listing. And keep the top layer clear: a deep layer of resin over the decoration adds a buffer between the mug and the design.
If you want to sell coasters or give them as gifts, test one from each batch with a hot mug for a few minutes before handing out the set. Coasters touch the bottom of cups, not food, but if you use them as small trays for snacks, check what your resin maker says about food contact after full cure.
Frequently asked questions
Can I use UV resin for coasters? It works for very thin coasters and for sealing a surface, but most UV resins cure poorly beyond a few millimeters, cost more per ounce and are not made for full 1/4 in pours. Two-part epoxy is the normal choice for coasters.
Why are my coasters cloudy or sticky? Cloudiness usually comes from moisture, cold or under-mixed resin, and stickiness almost always comes from a wrong ratio or unscraped resin from the cup walls. Measure exactly, mix for three minutes or more and work at 70 to 80 F.
Do I need mold release for silicone coaster molds? Not for new, glossy silicone molds. Use a release spray if the mold is old, textured or made of a hard plastic, or if earlier pieces have started to stick.
How long should coasters cure before use? Demold after 24 to 48 hours, then wait at least 72 hours before normal use and about a week before setting hot drinks on them.
What you need for this
- See price on AmazonAmazon
LET'S RESIN casting resin kit, 34 oz
From Best epoxy resin for silicone molds: clear casting picks
- See price on AmazonAmazon
LET'S RESIN 350W dual temp heat gun for resin
From Best heat gun for resin art: popping bubbles without damage
- See price on AmazonAmazon
LET'S RESIN mica powder set, 60 colors x 5 g
From Best mica powder and pigment powder sets for epoxy and UV resin
- See price on AmazonAmazon
TCP Global Graduated Mixing Cups, 10 oz, 50 Box
From Best epoxy resin mixing cups: silicone sets and graduated disposables