Epoxy resin vs polyurethane: thickness, durability, UV and cost

Published

As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.

Gear for this job

All 6 picks compared

Epoxy resin builds a thick, glassy coat in one pour and is the better choice for bar tops, river tables, filling voids and embedding objects. Polyurethane goes on in thin coats, keeps the look of the wood, resists scratches and sunlight better and is the usual choice for furniture, floors and outdoor wood. They are not rivals so much as tools for different jobs, and for a table that needs depth and durability, many woodworkers use epoxy for the build and polyurethane as the topcoat.

The core difference: build thickness

A table top epoxy self-levels to about 1/8 in in a single coat. That thickness is what gives the deep, wet look, fills cracks and knots, and buries coins, photos or bottle caps under a flat surface. One or two coats finish the job.

Polyurethane goes on a few thousandths of an inch per coat. It follows the surface instead of filling it, so the wood keeps its texture and looks like wood rather than wood under glass. A good finish needs three or more coats with light sanding between them, and gaps or cracks stay visible unless you fill them first.

Durability: scratches, impact and heat

Cured epoxy is hard but brittle compared with polyurethane. It resists stains, water and dents from light impacts well, but its glossy surface shows fine scratches from sliding dishes and keys, and a sharp blow can chip a thick coat at the edge. Polyurethane is more flexible and more abrasion resistant, which is why it is used on wood floors.

Neither is heatproof. Common art and table top epoxies soften at roughly 120 to 140 F, so a hot pan or a mug straight from the microwave can mark them. Cured polyurethane tolerates warm mugs a bit better, but a hot pan will also mark it. Use trivets on both.

Repairs differ too. A scratched polyurethane finish can be scuffed and given a fresh coat that blends in. A scratched or dull epoxy surface is wet sanded through finer grits and polished back to gloss, or sanded and given a new flood coat, which is a bigger job. Deep chips in epoxy can be filled with a drop of resin and sanded flush, but on a thick clear coat the repair can stay faintly visible.

See kits for buffing out epoxy scratches →

Sunlight and outdoor use

Epoxy has poor resistance to UV. In sun it yellows, then turns chalky and can crack, even in formulas with UV stabilizers, which slow the process rather than stop it. Polyurethane holds up better, and exterior or spar urethanes contain UV absorbers made for outdoor wood.

For outdoor tables, bar tops and boat parts, the standard approach is to use epoxy where its strength and water barrier matter, then cover it with a UV resistant varnish or two-part polyurethane. The topcoat takes the sun, and you renew it every year or two. Oil-based polyurethane ambers with age as well, while water-based polyurethane stays clearer.

Compare UV resistant epoxies →

Ease of application and fumes

Polyurethane is a one-part finish you brush, wipe or spray straight from the can. Mistakes are fixed by sanding and adding a coat. The trade-off is time: several coats with drying and sanding between them, and dust nibs to sand out.

Epoxy needs exact measuring and thorough mixing, a warm room at about 70 to 80 F, a level surface, bubble popping with a heat gun or torch and dust protection while it cures. A mistake with the ratio leaves soft or sticky spots that must be scraped off. Most craft epoxies are low odor, but you still need gloves and ventilation, and a respirator for large pours. Oil-based polyurethane has strong solvent fumes; water-based has much less.

Cure times also differ. Most table top epoxies can be recoated within a day and reach full cure in about 72 hours, with a week before heavy use. Oil-based polyurethane usually needs a day between coats and several weeks to reach full hardness, though it can be used lightly after a few days. Water-based polyurethane dries fastest, often allowing several coats in one day, but it builds even thinner per coat.

Compare heat guns for epoxy bubbles →

Cost and which to choose

Epoxy costs more per square foot because you use so much of it. A 1/8 in coat takes about 10 fl oz of mixed resin per square foot, so a dining table can use one to two gallons. A quart of polyurethane covers around 125 square feet per coat, so even several coats cost far less.

Choose epoxy for bar tops, river tables, resin art, embedded objects, filling deep cracks and live edges, and surfaces you want to look like glass. Choose polyurethane for furniture, cabinets, wood floors, doors, outdoor wood and anything where a natural wood look and easy repair matter more than depth. Use both when you want the depth of epoxy with a tougher, sun resistant surface: let the epoxy cure, scuff it with 220 to 320 grit, clean it and apply polyurethane.

See mixing cups for exact epoxy ratios →

Frequently asked questions

Can you put polyurethane over epoxy? Yes. Let the epoxy fully cure, wash off any blush, sand it to a dull finish with 220 to 320 grit and apply the polyurethane. It improves scratch and UV resistance.

Can you put epoxy over polyurethane? Yes, if the polyurethane is fully cured, scuffed and clean. Epoxy will not bond well to a glossy, unsanded finish.

Which is more waterproof? Both are water resistant when cured. Epoxy forms a thicker, more complete barrier and is used to seal boats; polyurethane needs several coats to match it.

Is epoxy harder than polyurethane? Epoxy is harder and stiffer, but polyurethane resists abrasion and small scratches better because it flexes.

What you need for this