Can you paint epoxy resin? How to paint over, under and into resin

Published

As an Amazon Associate we earn from qualifying purchases. This does not change our picks. Affiliate disclosure
New to Prime? Try Prime free for fast, free shipping on eligible items.

Gear for this job

All 6 picks compared

Yes, you can paint epoxy resin once it is fully cured, but paint will not stick to the glossy surface as it comes out of the mold. Scuff it with 220 to 320 grit sandpaper, clean off the dust and any oily film, apply a bonding primer, and then use acrylic, enamel or spray paint. You can also paint between resin layers or on the back of a clear piece, which gives a glossy, protected finish without any primer.

Why paint peels off resin

Cured epoxy is smooth, hard and non-porous. Paint has nothing to grip, so it dries as a skin sitting on top and peels or scratches off with a fingernail. Two other things make it worse. Mold release spray left on a cast piece repels paint, and some epoxies form amine blush, a slightly greasy film from humidity during the cure, which stops paint and new resin from bonding.

The resin must also be fully cured. Paint over epoxy that is still soft can wrinkle, stay tacky or react with uncured surface resin. Wait the full cure time on the label, usually 72 hours and up to 7 days for some brands, before you start.

Preparing the surface

Wash the piece with warm water, dish soap and a scrub pad. This removes amine blush and most mold release. Dry it fully.

Sand the whole area to be painted with 220 to 320 grit until the gloss is gone and the surface is evenly dull. On small or detailed castings, a sanding sponge or a fine abrasive pad reaches into curves better than flat paper. Wipe off the dust, then wipe the surface with isopropyl alcohol on a lint-free cloth and let it dry. From this point, handle it with gloves so skin oil does not get on it.

Mask anything that should stay glossy before you sand, such as a clear window in a casting or the face of a coaster, using painter's tape pressed down firmly at the edges. Sanded resin turns cloudy and needs polishing to clear again, so it is easier to protect those areas than to restore them afterward.

Compare sandpaper and polishing kits →

Primer and which paints work

A primer made for plastic or a bonding primer gives the best grip. Spray in two or three light coats rather than one heavy one, and let it dry as the can states. For small pieces, an acrylic gesso or a model primer works well.

Over primer, almost any paint works. Acrylic craft paint is the easiest for hand painting details and figurines. Spray enamel and acrylic spray paint give an even color on larger pieces. Oil paint works but takes a long time to dry. Paint pens, including oil-based markers, are handy for lettering and fine lines. Finish with a clear coat if the piece will be handled: a spray varnish for figures, or a thin coat of epoxy or UV resin for a glossy, hard surface.

Test before painting a finished piece. Prime and paint a scrap casting or the back of the piece, let it dry for a day, then press a strip of masking tape on it and pull it off quickly. If paint comes away with the tape, the surface needs more sanding or a different primer. This takes a few minutes and avoids stripping a painted piece later. Metallic paints and gold leaf adhesives are especially prone to lifting on smooth resin, so they benefit most from a good primer.

Painting between layers and on the back

Painting inside resin avoids most adhesion problems because new resin covers and locks in the paint. Pour a first layer, let it cure or reach a firm tack, lightly scuff it if it is fully cured, paint your design with acrylic paint or paint pens, let the paint dry completely, then pour the next layer. The result looks like it floats in glass. This is how layered 3D fish, landscapes and lettering in trays and coasters are made.

Reverse painting is the same idea for clear pieces: paint the back of a cured, sanded casting, working from details first to background last, then seal the back with resin or a clear coat. Let paint dry fully before covering it, because water or solvent trapped under resin can cloud it or cause bubbles. Thick acrylic layers should dry for several hours.

Compare clear epoxies for layered pours →

Coloring resin instead of painting it

If you want the whole piece colored, tint the resin before pouring instead of painting afterward. Resin dyes give a transparent, stained glass color, mica powders give shimmer, and opaque pastes give solid colors. Keep colorant to a small share of the mix, around 5 percent at most for most brands, so the epoxy still cures fully.

Acrylic paint can be stirred into epoxy in small amounts, and many crafters do it for opaque colors, but it contains water, and too much can make the resin cloudy, soft or slow to cure. Dedicated resin pigments do the same job without that risk, cost little, and need only a few drops per cup.

Compare epoxy resin dyes →

Frequently asked questions

Can you paint resin without sanding? Paint will stick poorly to glossy cured resin. A self-etching or plastic bonding primer helps, but a light scuff is still the most reliable preparation.

Can you spray paint epoxy resin? Yes. Scuff, clean and prime it, then use light coats of spray paint. Spray enamel and acrylic spray paints both work over primer.

Can you put resin over acrylic paint? Yes, once the paint is fully dry. Resin over acrylic paintings, canvases and painted wood is a common finish.

Can you paint a 3D printed resin model the same way? Yes. Wash and fully cure the print, sand away supports, prime with a model primer and paint with acrylics. That resin is a different material, but the paint steps are the same.

What you need for this