# Resin casting without a pressure pot: methods that work

Source: https://resinandmold.com/blog/resin-casting-without-pressure-pot
Published: 2026-10-01
Publisher: Resin and Mold

**Short answer:** You can cast clear resin without a pressure pot if you use a slow, thin epoxy in an open mold: warm the bottles 10 to 15 minutes, stir slowly for 3 to 5 minutes, pour in a thin stream and pop what rises. Fast-setting resins and closed molds with sharp corners, such as dice, are where a pot at 40 to 60 psi earns its place.

A pressure pot does one thing: it squeezes bubbles so small that they cannot be seen while the resin sets. Without one, the only way to a clear casting is to keep air out of the mix and give whatever gets in enough time to rise and escape. That is realistic with slow casting and deep pour epoxies in open molds. It is not realistic with resins that set in minutes. This page gives the method with the figures makers publish, says where it falls short, and explains pressure and vacuum.

## Do you need a pressure pot for resin casting?

Not for most epoxy work in open silicone molds. Bubbles leave a casting on their own if the resin is thin and stays liquid long enough. Alumilite says its Amazing Clear Cast cures overnight, which allows time for air bubbles to evacuate, and TotalBoat credits ThickSet's low viscosity and long working time with minimizing trapped bubbles.

| What you are casting | Without a pressure pot | Why |
| --- | --- | --- |
| Coasters, trays and other shallow open molds in casting epoxy | Works | Short path to the surface and a long working time |
| Blocks and spheres in deep pour epoxy, poured in layers | Works with care | Low viscosity and hours of working time let air rise |
| Flowers, wood and other inclusions | Works with extra steps | Inclusions carry air: dry them and wet them with resin first |
| Coating or art resin in a deep mold | Poor | Thick resin made for layers of about 1/8 in holds bubbles |
| Dice and closed molds with sharp corners | Hardest case | Air caught in corners and numbers cannot rise out |
| Fast urethane resin with minutes of working time | Not realistic | It sets before bubbles can rise, so makers give pressure settings |
| Small UV resin pieces | No pot needed | Rest 5 to 10 minutes, use a toothpick, cure in thin layers |

General guide based on maker data sheets: thin, slow resins release air, thick or fast ones trap it.

## How to cast resin without a pressure pot, step by step

These steps are for two-part casting or deep pour epoxy in a silicone mold. Work in a room of about 70 to 80 F, or the range on your label, and read the label's working time first: every pause below has to fit inside it. Size the batch with the [resin calculator](https://resinandmold.com/tools/resin-calculator) so you mix once.

1. Pick a thin, slow resin: a casting or deep pour epoxy, not a coating resin. Check the depth per layer on the label, up to 3/8 in for casting epoxy and 1 to 2 in for deep pour.
2. Stand the closed bottles in warm, not hot, water for 10 to 15 minutes. Warm resin is thinner and lets air out. Dry the bottles before opening. Working time drops by about 10 minutes.
3. Measure the way the label says, then stir slowly for 3 to 5 minutes, scraping the sides and bottom. Alumilite says to keep the stick in contact with the bottom of the cup so less air is stirred in.
4. Let the mixed cup rest so bubbles rise. Let's Resin gives 5 minutes for its casting epoxy. Skip the rest if your label says to pour without delay.
5. Pour slowly in a thin stream from low over the mold, into one spot, and let the resin spread into the corners by itself.
6. Run a toothpick along corners, edges and fine detail to free trapped air. For dried flowers, Let's Resin suggests dipping them in mixed resin or brushing on a coat before they go into the mold.
7. Give the surface a quick pass of a heat gun or torch to pop what has risen. Keep the tool moving and take care over silicone, which a flame can damage.
8. Check again every few minutes while the resin is liquid and repeat the toothpick and the heat pass. Stop once it starts to thicken, then leave the piece level for the full cure time.

## Why slow, thin resin is the key

A bubble needs two things to escape: resin thin enough to move through and enough time before the resin gels. Data sheets show how far products differ. EcoPoxy FlowCast has a mixed viscosity of 280 cP and a working time of 8 to 12 hours. Smooth-On EpoxAcast 690 is also 280 cP, with a 5 hour pot life. ArtResin, a coating resin, is **2,000 cP** mixed with 40 to 60 minutes of working time. That is why coating resins are kept to thin layers: see [casting resin vs coating resin](https://resinandmold.com/blog/casting-resin-vs-coating-resin).

Temperature matters as much. ArtResin describes cold resin as cloudy with micro bubbles too small to torch out, so warming the bottles is not optional in a cool room. Depth matters too: a pour deeper than the label allows overheats and bubbles late in the cure.

## Casting resin dice without a pressure pot

Dice are the hardest case. The mold is closed or capped, the corners are sharp and the numbers are tiny recesses, so air is held against the silicone where it cannot float out and no heat gun can reach it. A bubble that would go unnoticed in a coaster shows as a pit on a die face.

The method above still improves the odds: thin slow epoxy, warmed bottles, a slow stir and a toothpick worked into every number and corner before the cap goes on. Expect some rejects. A bubble at the surface can be sanded flat and covered with a thin clear coat. Bubbles inside a clear die stay there.

## How to tell the casting is bubble free

While the resin is liquid, look through the mold from the side against a bright light, where bubbles show as specks. Keep checking, because air keeps rising from the bottom and from inclusions. Once the resin starts to thicken, stop touching it.

After demolding, judge the result by where the bubbles are. Bubbles on the molded faces mean air was trapped against the mold: pour slower and work the corners next time. A milky haze of tiny bubbles through the whole piece means the resin was cold. Bubbles deep inside a cured piece cannot be removed. Fixes are in [how to get bubbles out of resin](https://resinandmold.com/blog/how-to-get-bubbles-out-of-resin).

## Why use a pressure pot, and is vacuum the same thing?

A pressure pot does not remove air. Smooth-On describes pressure casting as collapsing the bubbles into solution while the resin sets, and calls it the best method for bubble free castings. Makers give **40 to 60 psi**, and Smooth-On specifies 60 psi held until the resin gels. Use only a commercial pot rated for the pressure and never a homemade vessel: Smooth-On warns that these can explode. A rubber mold used under pressure must be made under pressure too, or its own bubbles show as dimples on the casting.

A vacuum chamber works before the pour: it pulls air out of mixed resin or silicone. Smooth-On says the pump must pull 29 inches of mercury. The material rises to 4 to 5 times its volume, and some epoxies must not be vacuumed at all, EpoxAcast 690 among them. In short, vacuum takes air out of the cup and pressure deals with air trapped in the mold. See the [vacuum chamber guide](https://resinandmold.com/best/best-vacuum-chamber-for-resin).

[Compare pressure pots for resin casting](https://resinandmold.com/best/best-pressure-pot-for-resin-casting)

## When it is time to buy a pressure pot

The careful method covers most open-mold epoxy projects. A pot makes sense when the mold or the resin takes away the time and the path that bubbles need.

- You cast dice, miniatures or other closed molds with sharp detail, and too many pieces come out with pits.
- You want to use a fast urethane resin. Alumilite lists about 7 minutes of working time for Alumilite Clear and gives pressure settings starting at 40 psi.
- You embed porous items such as unsealed wood, which release air into the resin during the cure.

Note: A pressure pot is a pressure vessel. Buy one made and rated for casting, keep to its rated pressure and do not modify it.

## Quick answers

Short answers on casting without a pot. Pressures and times are maker figures, and the instructions for your own resin and equipment come first.

- **Do you need a pressure pot for resin casting?** Not for slow epoxy in open molds. It is close to necessary for fast-setting resins and for dice or other closed molds.
- **Can you cast resin dice without a pressure pot?** Yes, with thin slow epoxy and a toothpick worked into every corner, but expect some dice with pits or small bubbles.
- **Can you cast resin without vacuum?** Yes. Warm bottles, a slow 3 to 5 minute stir and a short rest release most air from thin epoxy.
- **Why use a pressure pot for resin casting?** It shrinks trapped bubbles until they cannot be seen. Makers give 40 to 60 psi, held until the resin gels.
- **Resin casting: pressure or vacuum?** Vacuum removes air from the mix before pouring. Pressure deals with air trapped in the mold.

## Gear guides for this topic

- https://resinandmold.com/best/best-epoxy-resin-for-molds
- https://resinandmold.com/best/best-heat-gun-for-resin
- https://resinandmold.com/best/best-pressure-pot-for-resin-casting
- https://resinandmold.com/best/best-vacuum-chamber-for-resin

## Sources

- [Smooth-On: What is pressure casting?](https://www.smooth-on.com/support/faq/156/)
- [Alumilite: Amazing Clear Cast Technical Data Sheet (12/2020)](https://static1.squarespace.com/static/5a4de271017db281a04a84f1/t/60d7dcf4de3aff3e2a51454f/1624759543093/alumilite_tds_amazing-clear-cast_12-01-2020.pdf)
- [TotalBoat: ThickSet Clear Casting Epoxy Resin Tech Data Sheet (2019)](https://doc.jamestowndistributors.com/userportal/pdfs/TotalBoat/TotalBoat_ThickSet_Epoxy_TDS_4.11.19.pdf)
