# How to epoxy resin a table top: prep, seal coat, flood coat and cure

Source: https://resinandmold.com/blog/how-to-epoxy-a-table-top
Published: 2026-10-12
Publisher: Resin and Mold

To epoxy a table top, sand and clean the surface, brush on a thin seal coat to close the wood pores, then pour a self-leveling table top epoxy about 1/8 in thick, spread it to the edges and pop the bubbles with a heat gun or torch. Let it cure covered and dust free for at least 72 hours before light use. The work is mostly preparation: a warm room, a level table and enough mixed resin to finish the pour in one go.

## Choose the right epoxy and work out the amount

Use a table top or coating epoxy, not a deep pour casting resin. Coating epoxies are thicker, self-level at about 1/8 in and cure in a day; casting resins are thin, run off the edges and take days to harden. Most table top epoxies mix 1:1 by volume and give about 30 to 45 minutes of working time. For a table that stands in sunlight or outdoors, pick one that states UV resistance, and plan a UV-blocking topcoat for full sun.

At 1/8 in thick a square foot takes about 10 fl oz of mixed resin, so a 3 x 6 ft dining table needs about 180 oz, roughly 1.4 gallons, plus 15 to 20 percent for edges and absorption. The seal coat takes much less, about a third of that. Buy the full amount from one brand and batch before you start.

[Compare UV resistant table top epoxies](https://resinandmold.com/best/best-epoxy-resin-for-outdoor-use)

## Prepare the table and the room

Remove old finish that is flaking, then sand bare or finished wood to about 120 to 220 grit so the epoxy has something to grip. Vacuum and wipe with a lint-free cloth and denatured alcohol, and let it dry. Fill large knots and cracks with thickened epoxy or a first small pour and let them cure, otherwise they drain resin out of the flood coat and leave dips.

Set the table on blocks or buckets so resin can run off the edges cleanly, cover the floor with plastic, and check the top with a level in both directions. Work in a room at 70 to 80 F, and keep the resin bottles and the table at that temperature for a day before you pour. Cold wood and cold resin trap bubbles and cure cloudy. Turn off fans that blow dust, ventilate the room, and wear nitrile gloves and a respirator with organic vapor cartridges for a job this size.

[See respirators for resin work](https://resinandmold.com/best/best-respirator-for-resin)

## Apply a seal coat first

Wood holds air in its pores. When warm epoxy covers it, that air rises as bubbles, sometimes for an hour after the pour. A seal coat stops it. Mix a small batch, about 2 to 3 oz per square foot is plenty, and brush or spread it thinly over the top, the edges and any live edge, working it into the grain.

Let the seal coat cure until it is tacky to firm, usually 4 to 8 hours depending on the brand, then pour the flood coat within the recoat window your epoxy states. If you miss the window and the seal coat has fully hardened, scuff it with 220 to 320 grit, wipe off the dust and then pour, so the next layer bonds mechanically.

## Mix and pour the flood coat

Measure exactly by the method the maker states and mix for at least three minutes, scraping the sides and bottom of the bucket. For large tables mix in batches you can pour within the working time, about 1 to 1.5 gallons at a time; a big mass of mixed epoxy left in a bucket heats up and starts to set. Pour each batch onto the table right away, where spreading it thin lets the heat escape.

Pour in the center and in lines across the top, then spread the resin toward the edges with a plastic spreader or a notched trowel. Let it self-level to about 1/8 in and allow some to run over the edges. Use a foam brush to coat the vertical edges with the resin that drips down. After 10 to 15 minutes, check under the edges and scrape off hanging drips with a stick or gloved finger before they cure into hard beads.

[See large graduated mixing cups](https://resinandmold.com/best/best-epoxy-resin-mixing-cups)

## Pop the bubbles and protect the cure

Pass a heat gun or propane torch quickly over the whole surface a few inches away, keeping it moving. Do it again 15 and 30 minutes later, as wood outgassing can bring up more bubbles. Do not hold heat in one spot: it can scorch the resin or cause ripples. Pick out dust and hair with a toothpick while the resin is still liquid.

Cover the table with a clean tent of plastic sheeting on a frame, not touching the surface, to keep dust off. Most table top epoxies are dry to the touch in 12 to 24 hours, can take a second coat inside their recoat window, and reach full cure in about 72 hours. Wait at least 72 hours before putting objects on the table and about a week before heavy use, hot dishes or cleaning products.

[Compare heat guns for resin bubbles](https://resinandmold.com/best/best-heat-gun-for-resin)

## Second coats, fixes and finishing

One 1/8 in coat is enough for most tables. Add a second coat for a deeper look, to bury inlays or to fix flaws. Dust specks, small craters and drips that cured on the surface can be sanded flat with 220 to 400 grit and covered with another flood coat. Fish eyes, small round holes in the coat, usually come from oil, silicone or polish residue; sand, wipe with alcohol and recoat.

If you want a matte or satin finish, or a perfectly flat surface for a desk, wet sand the cured epoxy through finer grits and either polish it to a gloss or leave it at the satin level you like. Epoxy is softer than stone, so use coasters and trivets: most coating epoxies soften around 120 to 140 F and a hot pan will mark them.

[Compare resin sanding and polishing kits](https://resinandmold.com/best/best-resin-polishing-kit)

## Frequently asked questions

Can I pour epoxy over a painted or stained table? Yes, if the paint or stain is fully dry and cured, and you scuff and clean it first. Oil-based stains need several days to dry; epoxy over wet stain will not bond and can cloud.

How thick can I pour table top epoxy? Most coating epoxies are made for about 1/8 in per coat. For thicker finishes, pour several coats within the recoat window, or use a deep pour resin rated for the depth.

Why do I see bubbles hours after pouring? Air from the wood is still escaping. A seal coat prevents most of it; if it happens, a quick pass with heat within the first hour can still clear them.

Can I epoxy an outdoor table? Yes, with a UV resistant epoxy, but direct sun will still yellow it over time. A UV-blocking spar varnish or two-part polyurethane over the epoxy extends its life.

## Gear guides for this topic

- https://resinandmold.com/best/best-epoxy-resin-for-outdoor-use
- https://resinandmold.com/best/best-heat-gun-for-resin
- https://resinandmold.com/best/best-epoxy-resin-mixing-cups
- https://resinandmold.com/best/best-resin-polishing-kit
- https://resinandmold.com/best/best-respirator-for-resin
