# How much epoxy resin do I need? Formulas for molds, tables and coatings

Source: https://resinandmold.com/blog/how-much-epoxy-resin-do-i-need
Published: 2026-10-12
Publisher: Resin and Mold

You need the volume of the space you are filling: length x width x depth in inches gives cubic inches, and dividing by 1.805 gives fluid ounces of mixed resin. For flat coatings the shortcut is about 10 fl oz of mixed epoxy per square foot at 1/8 in thick, or roughly 1 gallon for 12 to 13 square feet. Add 10 to 15 percent for waste, drips and resin left in the cup. The sections below give the formulas for each shape, a ready chart for common tables and molds, and the mistakes that leave people short mid-pour.

## The basic formula and unit conversions

Every resin estimate is a volume. Measure in inches, multiply length by width by depth, and you have cubic inches. Then convert: 1 fl oz is 1.805 cubic inches, 1 US gallon is 231 cubic inches, and 1 liter is about 61 cubic inches. So a space of 100 cubic inches needs about 55 fl oz, or 0.43 gallon, of mixed resin.

Remember that the number is for mixed resin. A 1:1 kit sold as 1 gallon contains half a gallon of resin and half a gallon of hardener, which together make 1 gallon mixed. Most kits are labeled by their total mixed amount, but check, because a few list the resin part alone. If your epoxy is measured by weight, mixed epoxy weighs roughly 1.1 g per ml, so 1 fl oz of mixed resin is about 32 to 33 g; the exact density is on the maker's technical sheet.

[See graduated mixing cups](https://resinandmold.com/best/best-epoxy-resin-mixing-cups)

## Table tops, bar tops and flood coats

For a flat coating, multiply the area in square inches by the thickness. One square foot is 144 square inches, so at 1/8 in thick it takes 18 cubic inches, about 10 fl oz of mixed resin. At 1/16 in, a typical seal coat, it takes about 5 fl oz, and at 1/4 in about 20 fl oz.

A quick chart at 1/8 in thick, before waste: a 12 x 12 in board needs about 10 oz; a 2 x 4 ft coffee table (8 sq ft) needs about 80 oz, around 0.6 gallon; a 30 x 60 in desk (12.5 sq ft) needs about 125 oz, just under 1 gallon; a 3 x 6 ft dining table (18 sq ft) needs about 180 oz, around 1.4 gallons; a 2 x 8 ft bar top (16 sq ft) needs about 160 oz, around 1.25 gallons. Many table top epoxies state 1/8 in as the maximum for one coat, so a thicker finish means two coats, and the totals above double.

Coating jobs lose more resin than the formula shows. Resin runs over the edges, porous wood soaks up the first coat, and some resin stays on the spreader. Add 10 to 15 percent for a sealed surface and 20 percent or more for raw wood with open grain or live edges, or do a thin seal coat first so the flood coat is not absorbed.

[Compare epoxies for outdoor tables](https://resinandmold.com/best/best-epoxy-resin-for-outdoor-use)

## Molds: rectangles, rounds and odd shapes

For a rectangular mold, use the inner length x width x depth you plan to fill, not the outer size. A 9.5 x 6.6 in block filled 2 in deep is 125 cubic inches, about 70 fl oz. For a round mold, multiply 3.14 by the radius squared by the depth. A 4 in coaster at 1/4 in is 3.14 cubic inches, about 1.7 fl oz, and a 24 in round table mold filled 1 in deep is about 452 cubic inches, 250 fl oz or almost 2 gallons.

For spheres, letters, figurines and any odd shape, measure with water. Fill the mold with water to the level you will pour, empty it into a graduated cup and read the volume. Then dry the mold completely, because water left in silicone causes cloudy, bubbly resin. Rice works the same way and needs no drying. Many mold listings also state their resin capacity, which is worth checking against your own measurement.

[See large silicone molds with stated sizes](https://resinandmold.com/best/best-large-silicone-molds-for-resin)

## River tables and deep pours

A river table is mostly a volume problem. Measure the river at several points to get an average width, then multiply length x average width x depth. A 48 in river averaging 6 in wide and 2 in deep is 576 cubic inches, about 319 fl oz or 2.5 gallons. Add the flood coat over the whole top if you plan one, plus 10 to 15 percent for leaks and absorption by the wood edges.

Deep pour resins are sold by maximum depth per pour, often 1 to 2 in or more for slow casting resins, and the total you need does not change if you split it into layers. What changes is that you mix several batches, so buy a little more than the exact total. Running out of resin mid-layer is worse than having a few ounces left over, and leftover resin is easy to use for coasters.

## How much to add for waste, and common mistakes

Add 10 percent for small mold work, 15 percent for coatings over sealed surfaces, and 20 percent or more for raw wood, live edges and first-time projects. For very small batches under 2 oz, the share left in the cup is larger, so mix a little more than you think, or use a small cup so less resin coats the walls.

Common mistakes: measuring the outside of a mold, forgetting that kits list mixed volume, ignoring the maximum pour depth and planning one thick pour that has to become three layers, and mixing the whole amount at once for a large table. A big mass of mixed epoxy in one container heats up fast and can start to set in the bucket. Mix in batches you can pour within the stated working time.

## Frequently asked questions

How much epoxy do I need for a 4 x 8 sheet? A 4 x 8 ft surface is 32 sq ft, so a 1/8 in coat takes about 320 fl oz, around 2.5 gallons, before waste. Plan on about 3 gallons.

How many coasters does 16 oz of resin make? At about 1.7 to 2 oz per 4 in coaster 1/4 in deep, 16 oz mixed makes 7 or 8 coasters, allowing for waste.

How much resin does a tumbler need? A standard 20 oz skinny tumbler usually takes about 1 to 2 oz of mixed resin per coat, depending on how thick you apply it and how much drips off.

Is there a calculator? Yes, this site has a resin calculator that does the formulas above for rectangles, rounds and coatings once you enter the measurements.

## Gear guides for this topic

- https://resinandmold.com/best/best-epoxy-resin-mixing-cups
- https://resinandmold.com/best/best-epoxy-resin-for-molds
- https://resinandmold.com/best/best-large-silicone-molds-for-resin
- https://resinandmold.com/best/best-epoxy-resin-for-outdoor-use
