# Casting resin vs coating epoxy resin: depth, cure and uses

Source: https://resinandmold.com/blog/casting-resin-vs-coating-resin
Published: 2026-10-01
Publisher: Resin and Mold

**Short answer:** Both are two-part epoxy. Coating resin, also sold as art resin, is thick and made for layers of about 1/8 in (3 mm). Casting resin is thinner and fills molds up to about 3/8 in (10 mm) per layer, and deep pour resin takes 1 to 2 in. Choose by the depth of one pour, then check the limit on your own label.

The names on the bottles overlap. Epoxy resin, art resin, casting resin and deep pour are all epoxy mixed from Part A and Part B. What differs is how thick the liquid is, how deep one layer can be and how fast it cures. Those three go together: a resin that cures fast gives off its heat fast, so it has to stay thin. The figures below are maker data at 70 to 77 F and vary by brand, so the label on your bottle has the final word. One-part UV resin is a different product, compared in [UV resin vs epoxy resin](https://resinandmold.com/blog/uv-resin-vs-epoxy-resin).

## Casting resin vs coating resin vs deep pour: the numbers

Read across the row that matters for your project. Depth per layer is the row that decides most purchases: it is the deepest single pour the resin is made for, not the total depth of the piece. A deeper piece is built from several layers.

| Property | Coating / art epoxy | Casting epoxy | Deep pour epoxy |
| --- | --- | --- | --- |
| Depth per layer | About 1/8 in (3 mm) | Up to 3/8 in (10 mm) | 1 to 2 in, the label decides |
| Usual mix ratio | 1:1 by volume | 1:1 by volume, or by weight | 2:1 or 3:1 by volume |
| Working time | 40 to 60 minutes | 30 minutes to 5 hours | 30 minutes to 12 hours, by brand |
| Demold or hard to the touch | About 24 hours | 18 to 24 hours | 24 to 72 hours |
| Full cure | 72 hours | 72 hours | 5 to 7 days, some 7 to 14 |
| Thickness of the liquid | Thick, self-levels to about 1/8 in | Thinner, flows into mold detail | Very thin, stays liquid for hours so bubbles can rise |
| Made for | Top coats, doming, tumblers, sealing art | Coasters, jewelry and small molds | Blocks, spheres, flowers, thick castings |

Typical maker data at 70 to 77 F (ArtResin, Alumilite, TotalBoat, Smooth-On, EcoPoxy, MAS). Brands differ: check your label.

## How thick should epoxy resin be in one pour?

As thick as the label allows and no thicker. Coating epoxy is made for about **1/8 in (3 mm)**: ArtResin says its resin self-levels to that depth and should be built up in 1/8 in layers. Casting epoxy goes to about **3/8 in (10 mm)**: Alumilite gives that figure for Amazing Clear Cast and Smooth-On gives it for EpoxAcast 690.

Deep pour limits differ the most between brands. TotalBoat ThickSet allows 1 in per layer, or up to 2 in when casting in a small mold. MAS Deep Pour gives 1 in, EcoPoxy FlowCast 0.5 to 1.5 in and Smooth-On EpoxAcast 692 gives 1 1/2 in. The limit also depends on the mass: a wide, large pour holds more heat than a small mold of the same depth.

## What happens when coating resin is poured too deep

Epoxy makes heat as it cures. This is called exotherm. A thin layer loses that heat to the air and the mold. A deep layer of a fast resin traps it, the trapped heat speeds the reaction, and the reaction makes more heat. Alumilite's data sheet for Amazing Clear Cast says pouring beyond 3/8 in at one time can produce excessive heat that causes bubbling, cracks and deformations. TotalBoat ties its depth limit to preventing yellowing and excessive heat.

So a coating resin poured an inch deep into a mold can come out with bubbles frozen inside, cracks, a warped shape or a yellow tint. The same thing happens in the cup: a large batch left standing heats up and sets early. Mix only what one layer needs and pour it soon after mixing.

Note: The rated depth is for the room temperature on the label, usually 70 to 77 F. MAS warns that its deep pour resin may set too fast above 75 F, and Smooth-On recommends a cooler room for large pours.

## What happens when deep pour resin is used as a coating

The opposite mistake does less damage and costs more time. Deep pour resin is made to react slowly, and a thin film has very little mass to keep the reaction going. Smooth-On notes for its EpoxAcast resins that castings of 1/4 in or less cure more slowly. A deep pour resin spread as a top coat can stay soft for days, runs off edges because it is so thin, and collects dust while it waits.

A thin deep pour layer that is still soft after 72 hours is usually slow, not failed. Keep it in a warm room and give it the full cure time on the label, which is 5 to 7 days for many deep pour products. If it stays tacky after that, see [why epoxy resin stays sticky](https://resinandmold.com/blog/epoxy-resin-still-sticky).

## Choose coating resin when

Coating resin and art resin are the same kind of product. Its thickness is the point: it stays where it is put and cures hard in about a day.

- The layer is about 1/8 in (3 mm) or less: a top coat on a painting, a tray, a board or a tumbler.
- You want a domed edge on a coaster, a bezel or a piece of jewelry. Thick resin holds a dome and thin resin runs off.
- You are adding a gloss coat to a piece cast in a matte mold, or covering a surface that has been sanded.
- You need the piece hard to the touch in about 24 hours and fully cured in 72 hours.

## Choose casting or deep pour resin when

Both are thin so that bubbles can rise and the liquid can fill detail. The depth of the mold decides between them, and so does how long you can wait.

- The mold is up to about 3/8 in (10 mm) deep, such as coasters, keychains and small shapes: choose casting epoxy and demold in 18 to 24 hours.
- The mold is 1 to 2 in deep, such as cubes, spheres, pyramids and flower blocks: choose deep pour epoxy and plan for 24 to 72 hours before demolding.
- You are embedding flowers or objects and need long working time for bubbles to rise out. Deep pour resins stay liquid for hours.
- The mold has fine detail. Thin resin reaches corners that thick coating resin bridges over.
- You can wait. A full cure takes 72 hours for casting epoxy and 5 to 7 days or more for deep pour.

[Clear casting epoxies for molds](https://resinandmold.com/best/best-epoxy-resin-for-molds)

## Filling a deep mold with the resin you already have

A resin with a low depth limit can still fill a deep mold in layers. Divide the mold depth by the depth per layer and round up. A 2 in cube takes 6 layers of casting epoxy at 3/8 in, or 2 layers of a deep pour resin rated for 1 in. The [resin calculator](https://resinandmold.com/tools/resin-calculator) gives the total amount, the number of layers and the amount per layer, and the [mixing ratio calculator](https://resinandmold.com/tools/resin-mixing-ratio-calculator) splits each batch into Part A and Part B.

When to pour the next layer depends on the maker. Alumilite allows layers of Amazing Clear Cast 3 to 4 hours apart and asks for sanding between layers after 12 hours. TotalBoat says to pour when the last layer has cooled and can still be dented with a fingernail. Smooth-On asks for a full cure between layers of EpoxAcast. Follow the recoat time on your label, and see the [epoxy cure time chart](https://resinandmold.com/blog/epoxy-resin-cure-time-chart) for typical times.

## Quick answers

Short answers to the searches behind this page. Depths and times are typical maker data at 70 to 77 F, and your label decides.

- **What is the difference between casting and coating resin?** Coating resin is thick and cures in thin layers of about 1/8 in. Casting resin is thin, cures slower and can be poured 3/8 in deep or more.
- **Is casting resin the same as epoxy resin?** For clear hobby resins, yes: casting resin is a thin epoxy. Epoxy resin is the family name, and coating, casting and deep pour are types within it.
- **Casting resin vs deep pour: which one?** Casting epoxy for molds up to about 3/8 in deep, deep pour for 1 to 2 in per layer. Deep pour takes 24 to 72 hours to demold.
- **Art resin vs casting resin?** Art resin is a coating epoxy. ArtResin, for example, self-levels to about 1/8 in, is dry to the touch in about 24 hours and fully cured in 72 hours.
- **What are the types of casting resin?** Casting epoxy, deep pour epoxy and one-part UV resin for layers of 2 to 3 mm. Polyurethane and polyester casting resins are separate products with their own rules.

## Gear guides for this topic

- https://resinandmold.com/best/best-epoxy-resin-for-molds
- https://resinandmold.com/best/best-epoxy-resin-for-tumblers
- https://resinandmold.com/best/best-resin-molds-for-flowers

## Sources

- [Alumilite: Amazing Clear Cast Technical Data Sheet](https://static1.squarespace.com/static/5a4de271017db281a04a84f1/t/60d7dcf4de3aff3e2a51454f/1624759543093/alumilite_tds_amazing-clear-cast_12-01-2020.pdf)
- [TotalBoat: ThickSet Clear Casting Epoxy Resin Tech Data Sheet](https://doc.jamestowndistributors.com/userportal/pdfs/TotalBoat/TotalBoat_ThickSet_Epoxy_TDS_4.11.19.pdf)
- [Smooth-On: EpoxAcast 690 and 692 Technical Bulletin](https://www.smooth-on.com/tb/files/EPOXACAST_690_TB.pdf)
