# Best UV resin for jewelry making: clear, hard and low odor

Source: https://resinandmold.com/best/best-uv-resin-for-jewelry
Updated: 2026-11-09
Publisher: Resin and Mold. Picks are chosen from what each Amazon listing states, not from hands-on tests. Method: https://resinandmold.com/how-we-pick

UV resin for jewelry making needs to do three things: flow into a bezel or a small mold, cure hard instead of bendy, and come out from under the lamp without a sticky surface. Hard type resins are sold for exactly that, and the bottles look much alike, so this guide compares six of them by what their Amazon listings state: cure time, the lamp the listing names, viscosity, hardness and total weight. Nothing was cured for this guide. Low viscosity resin, around 2000 cps where a figure is given, runs into small molds; none of these listings is a thick doming formula. Tack-free, low odor and anti-yellowing statements are the makers' claims and are reported that way. None of the listings states a lamp wavelength; jewelry resin lamps sit in the 365 to 405 nm band, and for a pendant or bezel layer around 2 mm deep, count on 30 to 90 seconds with a UV-LED lamp; a 36 W tube lamp needs 2 to 4 minutes for the same depth. If a cured pendant feels hard but has a slight tacky skin, that is common with hard type UV resins; isopropyl alcohol on a cloth takes it off.

## Picks

### 1. KISREL UV Resin 300g, Hard Type UV Resin Kit for Craft Jewelry Making

Weight: 300 g; Type: Hard; Viscosity: not stated; Cure time: 1-3 min with 36 W lamp

A 300 g bottle of hard type UV resin sold for jewelry making. The listing states a 1 to 3 minute cure under a 36W UV lamp and a hard, non-stick surface after curing.

What the listing offers:
- Names the lamp and the time: 1 to 3 minutes of curing under a 36W UV lamp.
- The product page states the cured piece is hard, non-stick and crystal clear, with a reduced odor formula.
- Described as self-leveling, and the spec sheet says mica powder, colorants, glitter and sequins can be mixed in.

Limits to know:
- No viscosity or hardness figure is given, so there is no number to compare with the 2000 cps resins.
- The listing advises not touching a piece right after curing, until it has cooled, to avoid leaving fingerprints.

### 2. Craft Resin UV Resin Kit - Hard Type, Low Viscosity Crystal Clear - 500g | Improved Formula, Fast Cure Under UV Light, UV Resin Glue for DIY, Jewelry Making, Molds Casting and Polymer Clay Projects

A 500g hard type, low viscosity UV resin kit from Craft Resin, supplied as five 100g bottles, aimed at jewelry, small molds, bezels and polymer clay coating.

What the listing offers:
- Same brand as the earlier pick and the same 500g total, split into five 100g bottles, so a bottle can be opened as needed.
- Low viscosity flow is stated for tiny bezels and mini molds, and the hardness is given as 85D with under 2% shrinkage.
- The listing names a 1 to 3 minute cure with the maker's 24W UV light and describes the resin as low odor, no mixing and anti-yellowing.

Limits to know:
- The quoted cure time is tied to the maker's own 24W lamp, so cure times with another lamp are not stated.
- Low viscosity resin runs, so it is a poor choice for doming or thick coats compared with a high viscosity formula.

### 3. Bsrezn 400g UV Resin Crystal Clear, Hard UV Epoxy Resin Cure for Jewelry

Cure time: not stated; Lamp named: not stated; Viscosity: 2000 cps; Hardness: 85D

400 g (14 oz) of hard UV resin in four bottles. The listing states a low viscosity of 2000 cps, a hardness of 85D and shrinkage under 2 percent, and names earrings and pendants as uses.

What the listing offers:
- States three figures: viscosity 2000 cps, hardness 85D and a shrinkage rate under 2 percent.
- Four separate bottles keep unused resin sealed, and the product page names earrings and pendants as typical pieces.
- The listing advises translucent silicone molds so UV light reaches the resin from all directions.

Limits to know:
- No cure time and no lamp wattage or wavelength appear in the spec sheet bullets.
- The yellow-resistant finish is the maker's claim; the manufacturer gives no test or time span for it.

### 4. LET'S RESIN UV Resin, 300g Hard Resin Kit for Craft, Casting, Silicone Mold

Weight: 300 g; Type: Hard; Viscosity: 2000 cps; Cure time: Minutes (lamp not stated)

A 300 g hard UV resin for casting and silicone molds. The listing states a low viscosity of 2000 cps, shrinkage under 2 percent and curing with UV light in minutes, without naming a lamp.

What the listing offers:
- Viscosity is stated at 2000 cps, and the product page says it flows smoothly into tiny molds.
- Less than 2 percent shrinkage is stated, and resin earrings are named among the uses.
- The spec sheet describes a low odor formula with enhanced anti-yellowing properties, as the maker's claim.

Limits to know:
- Cure time is given only as minutes, and no lamp wattage or wavelength is named.
- High hardness is claimed without a Shore figure, unlike the two 85D listings in this guide.

### 5. ULLFEU UV Resin Kit 1000g Bulk, No Odor Clear Hard Fast Epoxy Resin Kit

Cure time: 1-3 minutes; Lamp named: UV lamp, no wattage; Viscosity: not stated; Hardness: not stated

A 1000 g bulk pack of clear hard UV resin. The listing states 1 to 3 minutes under a UV lamp on the front and back of the mold and names earrings, rings, pendants and keychains.

What the listing offers:
- States the method: a UV lamp on the front and back of the mold for 1 to 3 minutes.
- 1000 g suits people making jewelry in volume, and the product page names earrings, bracelets, rings and pendants.
- The spec sheet says active diluents were added to reduce VOCs and odor, and antioxidants to resist yellowing.

Limits to know:
- No lamp wattage, viscosity or hardness figure is stated, so it is hard to compare on numbers.
- A kilogram is a lot for occasional pendants, and the title's no odor wording is the maker's claim.

### 6. YIEHO 300g UV Resin Glue Crystal Clear, Hard UV Epoxy Resin for Crafting

Weight: 300 g; Type: Hard; Viscosity: Low (no figure); Cure time: not stated

A 300 g bottle of hard type UV resin. The listing names its ingredients, mentions a Safety Data Sheet and REACH requirements and describes low viscosity, but gives no cure time or lamp.

What the listing offers:
- The spec sheet names the resin chemistry: bisphenol A epoxy acrylate, polyurethane acrylate and epoxy acrylate.
- States that a Safety Data Sheet is available and that the ingredients meet REACH requirements.
- Comes with a detailed instruction manual covering how to avoid bubbles and improve curing, per the product page.

Limits to know:
- No cure time, lamp wattage or wavelength is stated in the spec sheet bullets.
- Low viscosity and super hard are claimed with no cps or Shore figure to compare.

As an Amazon Associate I earn from qualifying purchases.